Theme
Digital Transformation
Green Transformation
CLAMPTEK ENTERPRISE CO., LTD.
Product Description :
＊High supporting force
CSP-P/ CSP-K increases the holding force between the piston rod and the inner jacket to arise the higher supporting force.
＊Coolant cleaning measures
In order to prevent the malfunction from the intrusion of high-pressure coolant and the cutting dust entering the internal structure, air can be cleaned at the breathing port when replacing the workpiece. Air cleaning requires a dedicated air circuit. (recommended cleaning pressure is 0.3 - 0.5MPa).
＊Universal piping base
CSP-P/ CSP-K piping base is interchangeable, which can be installed with other low-pressure cylinders in the same specifications.
Parjet Co.,Ltd.
Product Description :
PTFE Glide seal sets consists of a PTFE sealing element with a rubber O-ring functioning as elastic energizer. This type of Teflon seal is mainly used to seal reciprocating rods, pistons, and plungers, commonly found in hydraulic and pneumatic applications. The required sealing effect is achieved by radial pressure, produced by the preloaded element and system pressure, on the lip against mating surface. The elastic energizer pushes the PTFE ring against the mating surface which provides the initial sealing force for the PTFE seal.
FUTECH PRECISION CO.,LTD.
Product Description :
Ultra-short, high speed, light weight.
Designed with a detection device, which can be equipped with an inductive proximity switch.
Easy to adjust to ensure the correct operation of the hydraulic cylinder.
Built-in safty self-locking valve and pressure relief valve.
Dual-purpose type, can be installed by the front and rear ends.
The oil pipe must be connected to the oil pressure tank separately to avoid back pressure.
HYDROKOMP GmbH
Product Description :
Coupling elements of HYDROKOMP are made of stainless materials. This enables the elements to be used for all fluids and gases that are not aggressive. Special designs eg. for water steam or other media are available on request. HYDROKOMP offers coupling elements for two different operating modes depressurized coupling or pressurized coupling. The elements for depressurized coupling can be coupled pressurized up to 25 bar, if the specified volume flow is not be exceeded. When using higher operating pressure there ockures a risk of demaging the soft seal in the check valve as the result of high flow velocities of the fluid. This means for coupling of air up to 10 bar there should be always used the coupling elements for depressurized coupling. This also applies when the coupling process is initiated pressurized. The elements which can be coupled pressurized may be coupled up to the maximum specified operating pressure on one side and / or on both sides.
Parjet Co.,Ltd.
Product Description :
HiPerSeal®, aka Spring Energized Seal and Teflon Spring Seal, is a U-shaped machined performance polymer that utilizes a single spring energizer to provide force for the sealing lips. The seal jacket is made from PTFE compounds using high-performance polymer fillers to enhance overall spring seal life and wear resistance properties. The system pressure ultimately increases the sealing force and creates a leak tight seal. Because the spring loaded seal utilizes a spring, slight misalignment is tolerated, and the sealing force and jacket wear is more consistent. Spring energizers are available in corrosion resistant metal alloys such as stainless steel, Elgiloy and Hastelloy to meet the most serious corrosive and high temperature applications. We offer a wide variety of springs energizers including Canted Coil springs, Helical springs and Cantilever springs. For more information, you may refer to the tab "Spring" under "Products".
Parjet Co.,Ltd.
Product Description :
ParSave® - Bearing Isolator, is an extension of Parjet PTFE products. It is a sealing device developed to protect the rolling bearings of rotary equipment and can replace traditional lip seals (also known as rubber oil seals). The special configuration of the labyrinth ring combination helps to eliminate common sealing issues. Common issues includes the shaft damages caused by the wear of the rotating shaft from the lip seals and malfunction caused by the intrusion of foreign objects or water vapor. ParSave® can effectively extend the service life of the bearings and rotating shafts. Additionally, due to the unique sealing mechanism, there is no contact between mating surfaces, so there are no potential wear and pollution problems. With the characteristics of the PTFE material such as excellent heat resistance, self lubrication and chemical resistance, ParSave® can operate effectively under harsh environments.
CLAMPTEK ENTERPRISE CO., LTD.
Product Description :
The Thread-body single acting hydraulic cylinder use imported oil seal and accessories to guarantee the quality. No oil leakage while clamping in high pressure for a long time. The volume of the thread-body single acting hydraulic cylinder is small. It can be utilized in a small space in the fixture.
This hydraulic cylinder is used to extend out, and when spring returns, but it can't be used for pulling back.
The angle degree between the cylinder and workpiece could not be larger than 10° while installing.
The bottom of the cylinder barrel needs a leakage-proof gasket.
Max. operating pressure: 250 kgf/cm²
Min. operating pressure: 20 kgf/cm²
Single acting
Usable fluid:
Parjet Co.,Ltd.
Product Description :
Parjet has become a leader in the sealing industry by providing a full range of sealing solutions. For every complex seal application, Parjet has a solution.
Mechanical shaft seals are often an ideal sealing method. They provide the most suitable sealing method under many conditions especially high temperatures, high pressures, high viscosity (sediment), high speeds, large diameters, and many others. Most importantly, we have a highly technical mechanical seal providing and customizing the most optimal sealing solution for you.
HYDROKOMP GmbH
Product Description :
Swing clamp cylinders release the clamping point on the workpiece. With this, it is easy to change the workpiece. This hydraulic swing clamp cylinder operates as single-acting or double-acting traction cylinder, whereas part of the stroke is used to rotate the piston. The model with 0° swing angle operates only vertical as traction cylinder.
To guarantee a long lifetime the cylinders have an integrated metal wiper as standard. For oil supply, the cylinders are equipped with threaded port and manifold port with O-ring for drilled channels. You can select between right or left turning models with various standardized swing angles. The integrated overload protection protects the swing mechanism from damage due blockage of the rotation or improper assembly of the clamping arm.
For any risk of exceeding the permitted volume flow a throttle check valve must be interposed into the oil supply line. Counter-hold the clamping arm when tightening or loosening the counter nut in order to prevent torque transfer to the piston rod and to avoid damage to the ball guide. Variations with 0°, 30°, 45°, 60° and 90° swing angles are available. The permitted operating pressure is depending from the clamping arm length.
CLAMPTEK ENTERPRISE CO., LTD.
Product Description :
Clamptek’s CLF5H series designed with connecting rod structure which can operate conveniently. CLF5H series can also reduce the interference with loading and unloading operation, because when CLF5H series is in the unclamping state, it’s clamping arm can be put lower than holding position.
Clamptek’s CLF5H series’ clamping arm is very flexible. By reducing the interference of the surrounding equipment, CLF5H series can save lots of working space.
Clamptek’s CLF5H series equipped with special dust proof design and high sealing, which can prevent the cutting chips and coolant to infiltration. Therefore, CLF5H series can be used in more severe conditions.
Please kindly check the suggested operating pressure as below,
Max. operating pressure: 70 kgf/cm2
Min. operating pressure: 10 kgf/cm2
