Theme
Digital Transformation
Green Transformation
WEXTEN PRECISE INDUSTRIES CO., LTD.
Product Description :
■ Full series of inverter compressors are smooth start. There is no-start instantaneous high current and saving power more than 33%.
■ Unique design of multi-function LCD panel and it's provides -0.10°C temperature control stabilization.
■ There are 15 malfunction protection to ensure normal operation of cooler.
■ When low heating load is happend,the cooler will operate in low load mode and combined accurate temperature control and energy saving.
■ Groove recessed panel design is reducing oil mist infiltration into electrical control unit.
■ Using high-efficiency heat exchanger to enhance cooling efficiency.
■ Using high-efficiency environmental refrigerant and without pollution.
■ Up-to 95% materials of machine are recyclable and eco-friendly.
FUTECH PRECISION CO.,LTD.
Product Description :
Ultra-short, high speed, light weight.
Designed with a detection device, which can be equipped with an inductive proximity switch.
Easy to adjust to ensure the correct operation of the hydraulic cylinder.
Built-in safty self-locking valve and pressure relief valve.
Dual-purpose type, can be installed by the front and rear ends.
The oil pipe must be connected to the oil pressure tank separately to avoid back pressure.
HYDROKOMP GmbH
Product Description :
Coupling elements of HYDROKOMP are made of stainless materials. This enables the elements to be used for all fluids and gases that are not aggressive. Special designs eg. for water steam or other media are available on request. HYDROKOMP offers coupling elements for two different operating modes depressurized coupling or pressurized coupling. The elements for depressurized coupling can be coupled pressurized up to 25 bar, if the specified volume flow is not be exceeded. When using higher operating pressure there ockures a risk of demaging the soft seal in the check valve as the result of high flow velocities of the fluid. This means for coupling of air up to 10 bar there should be always used the coupling elements for depressurized coupling. This also applies when the coupling process is initiated pressurized. The elements which can be coupled pressurized may be coupled up to the maximum specified operating pressure on one side and / or on both sides.
RAISE PRECISION CO., LTD.
Product Description :
Our range of optical sensors comprises classic forked light barriers with red light or infrared technology. Still greater accuracy is offered by our laser light barriers, which even respond to tiny objects.
The special design with integrated air system is an optimal solution when it comes to contamination, as the air system prevents dust and dirt from collecting on the transmitter and receiver.
A further CAPTRON innovation is the product series of TCP measurement units with laser. TCP measurement units ensure a highly precise tool calibration and precise XYZ measurement in industrial robots. TCP measurement units are commonly used in robot-based automation processes in the metering and bonding technology, welding, soldering and in the food industry.
WEXTEN PRECISE INDUSTRIES CO., LTD.
Product Description :
■All models use DC inverter compressors with smooth start-up, no instantaneous large
starting current characteristics, and low power consumption.
■When the heat load is low, the cooling unit operates at a low load, with high energy efficiency.
■The exclusive design of the multi-function LCD panel with an accuracy of ±1℃ can keep the
electric cabinet at a constant temperature, control heat sources, and improve the lifespan of
electronic components.
■ Uses environmentally friendly refrigerants with low Global Warming Potential (GWP) values.
■More than 95% of materials that can be recycled, contributing to environmental protection.
CHUAN TAI HYDRAULIC MACHINERY CO., LTD.
Product Description :
In order to solve the problem of difficult cleaning, the market developed so-called box-shaped filters, but still can not completely solve
1 takes up too much space
2 Multiple pump combination systems must be configured one-to-one, resulting in too many connectorsProne to oil leakage
In order to solve the above problems, the company has developed a pair of two-box external magnetic flange filters to reduce space and prevent oil leakage problems, reduce assembly time and parts costs
CHANGHUA CHEN YING OIL MACHINE CO., LTD.
Product Description :
1. CEN03 type is without timer (also could be controlled by Programmable Logic Controller) and has to work with volume distributors. With CAB or CBB type volume distributor, oil will feed during operation time. With CDB or T type volume distributor, oil will feed during interval time.
2. The discharge volume is fixed. The lubrication points of volume distributor supply a fixed flow of oil.
3. It has a spark-eliminator inside to prevent the sparks producing when the electric current is running. The spark-eliminator can avoid PLC (Programmable Logic Controller) being interfered.
4. CEN03 type has a pressure switch device and been set up as 8kg/cm2, which assures the oil volume of lubrication point and check if the piping works normally. The standard specification is NC (Normal Close) contact, which means if the pressure is abnormal, it will have signal. NO (Normal Open) contact is available on request.
5. It has a float switch that can detect the oil volume. When oil is lower than the minimum level, the float switch will automatically send a continuous signal.
6. It has a pressure gauge where an operator can check the pressure easily.
7. Do not press the force feed-oil (F button) more than three minutes in order to avoid overloading. When the temperature reaches 100℃, the sensor will be on to stop the motor continuing running about 5 minutes.
8. It can be used for the machines requiring strictly rationing oil flow. It is usually used for such as processing machines or projecting machines.
Parjet Co.,Ltd.
Product Description :
HiPerSeal®, aka Spring Energized Seal and Teflon Spring Seal, is a U-shaped machined performance polymer that utilizes a single spring energizer to provide force for the sealing lips. The seal jacket is made from PTFE compounds using high-performance polymer fillers to enhance overall spring seal life and wear resistance properties. The system pressure ultimately increases the sealing force and creates a leak tight seal. Because the spring loaded seal utilizes a spring, slight misalignment is tolerated, and the sealing force and jacket wear is more consistent. Spring energizers are available in corrosion resistant metal alloys such as stainless steel, Elgiloy and Hastelloy to meet the most serious corrosive and high temperature applications. We offer a wide variety of springs energizers including Canted Coil springs, Helical springs and Cantilever springs. For more information, you may refer to the tab "Spring" under "Products".
CLAMPTEK ENTERPRISE CO., LTD.
Product Description :
＊High supporting force
CSP-P/ CSP-K increases the holding force between the piston rod and the inner jacket to arise the higher supporting force.
＊Coolant cleaning measures
In order to prevent the malfunction from the intrusion of high-pressure coolant and the cutting dust entering the internal structure, air can be cleaned at the breathing port when replacing the workpiece. Air cleaning requires a dedicated air circuit. (recommended cleaning pressure is 0.3 - 0.5MPa).
＊Universal piping base
CSP-P/ CSP-K piping base is interchangeable, which can be installed with other low-pressure cylinders in the same specifications.
CHANGHUA CHEN YING OIL MACHINE CO., LTD.
Product Description :
1. Fixed amount of oil feeding that can supply the required amount of oil to each lubricating point.
2. There are various choices of discharge volume, 0.1, 0.2, 0.3, 0.4 and 0.5cc per stroke. The discharge volume of each outlet can be different.
3. Each discharge outlet has a detective piston that can detect if the pipe system works functionally.
4. T type 0.5cc can be assembled either NO (Normal Contact) or NC (Normal Close) Contact sensor switch. It also can be set up as NO or NC Contact upon request. When it is set up as NO Contact, it sends signal during the operation time. When it is set up as NC Contact, it sends signal during the interval time.
5. T type volume distributors accumulate oil inside of the distributor and discharge oil during the interval time.
6. T type volume distributors have to work with oil pressure-relief type lubricators. The lowest operation pressure is 8 kgf/c㎡ and the max pressure is 30 kgf/c㎡.
7. The viscosity range of oil is 32 ~90 cSt @ 40℃.
HABOR PRECISION INC.
Product Description :
> Applications
CNC Machining Center、CNC Grinding machine、Broaching machine、CNC Wood-working 、Machine、CNC Mechanical Press、CNC Lathe、High Speed Lathe
Hydraulic Unit
High Speed Spindle
> Feature
Prevent temperature increasing of spindle, improve working precision of machine.
Prevent deviation of spindle center line or heat deformation of machine.
Extend the lifetime of the machine.
Stabilize oil pressure, prevent oil vibration.
Easy operation, low noise.
