展覽主題
數位轉型
綠色轉型
培凱有限公司
產品描述 :
[軸承隔離器]顧名思義是針對轉動設備滾動軸承的保護而開發的密封裝置，可取代傳統的唇形密封件(亦稱為橡膠油封)，利用特殊配置的迷宮環組合，不但消除了轉動軸被唇形密封磨損而導致的軸心磨損，其軸承也因異物或水氣的侵入而引起潤滑油的劣化&失效問題，軸承隔離器可有效延長軸承與轉動軸心的使用壽命。另外因無對磨面的接觸故也無元件磨耗與汙染問題，整個密封件材料以耐熱自潤性及高強度的特殊填料聚四氟乙烯成搭配FKM (Viton) O型環非常適用於軸承轉動設備嚴苛的環境。
HYDROKOMP GmbH
產品描述 :
The rotary lever clamp is especially suited for clamping fixtures with only little space for the installation of clamping elements. Its construction and compact design allows flexible solutions at various installation conditions. HYDROKOMP offers hydraulic rotary lever clamps which are single-acting as well double-acting. They are used in clamping fixtures whose oil supply is made through drilled channels. To swing down the clamping arm, the linear motion is used pro rata which clamps the workpiece. To unclamp, the clamping arm swings back to where the workpiece can be safely taken out.
HYDROKOMP GmbH
產品描述 :
Coupling elements of HYDROKOMP are made of stainless materials. This enables the elements to be used for all fluids and gases that are not aggressive. Special designs eg. for water steam or other media are available on request. HYDROKOMP offers coupling elements for two different operating modes depressurized coupling or pressurized coupling. The elements for depressurized coupling can be coupled pressurized up to 25 bar, if the specified volume flow is not be exceeded. When using higher operating pressure there ockures a risk of demaging the soft seal in the check valve as the result of high flow velocities of the fluid. This means for coupling of air up to 10 bar there should be always used the coupling elements for depressurized coupling. This also applies when the coupling process is initiated pressurized. The elements which can be coupled pressurized may be coupled up to the maximum specified operating pressure on one side and / or on both sides.
HYDROKOMP GmbH
產品描述 :
Swing clamp cylinders release the clamping point on the workpiece. With this, it is easy to change the workpiece. This hydraulic swing clamp cylinder operates as single-acting or double-acting traction cylinder, whereas part of the stroke is used to rotate the piston. The model with 0° swing angle operates only vertical as traction cylinder.
To guarantee a long lifetime the cylinders have an integrated metal wiper as standard. For oil supply, the cylinders are equipped with threaded port and manifold port with O-ring for drilled channels. You can select between right or left turning models with various standardized swing angles. The integrated overload protection protects the swing mechanism from damage due blockage of the rotation or improper assembly of the clamping arm.
For any risk of exceeding the permitted volume flow a throttle check valve must be interposed into the oil supply line. Counter-hold the clamping arm when tightening or loosening the counter nut in order to prevent torque transfer to the piston rod and to avoid damage to the ball guide. Variations with 0°, 30°, 45°, 60° and 90° swing angles are available. The permitted operating pressure is depending from the clamping arm length.
台灣嘉剛國際股份有限公司
產品描述 :
此系列產品設計中採用連杆機構, 在解除夾持狀態時, 壓臂可拉到低於夾持面的位置, 減少對工件裝卸的干涉, 因此操作方便, 缸體採用一體成型。
產品動作軌跡非常小, 用傳統的轉角缸/ 杠杆缸都難以夾持到的部位均可以達到夾持作用, 並可以減少對周圍機器設備的干擾, 達到節省工作空間的目的。產品採用了專用防塵設計, 防止了切削及冷卻液的滲入, 實現了高密封性, 因此在比較惡劣的環境下也能使用。
最大操作壓力：70 kgf/cm2
最小操作壓力：10 kgf/cm2
